jetstream1

Now thats funny whats the odds of that..The League in florida tends to stay with the same sponsor one of my sons is in coach pitch and the other is in minors just cause the other guy has a biz. A sponsor is a sponsor. and they are needed all around

Yes it will.

I used tie straps for mine I think u-bolts will hold it just fine just one thing about them tanks the walls on them are not that thick I think it will bust one day but hey I get em all day long for $30-50 bucks I just went to the T.S.C store and got a 125 leg stand tank for my chem and paid 225 for it..so the cage tank works fine

Just did my trailer with the roll on truck stuff for the bed

What did you start them out at? I got my start is pressure washing from someone who had a good thing going at one time. work with him for 3 years and then he started messing with my pay...So gave him the one finger wave after that he started to slowly droping work..and now well he sold out.So I went back to fence installing and then my body was telling me to stop. Here I stand 7 years with my own pressure washing...And body still hurts....Hang in there someone will go to work for you and stick to you like a leach...Then it will be the keys to the truck in hand and him/her running a crew like they owned it..on time and make sure the work gets done ....Good luck

Just got my first state job ! far as they pay I have no clue yet and best of all they called me. This work is good for one year. All I have to do is wash steps going in to the springs on a BI-weekly service. Will be nice in summer time but the winter with the florida costal wind will sux Who knows maybe this will lead to more state work

I pull about 60-75 a truck unless there is more

This has been a up and down year so far I have 2 bids for around 40-60 k a year and have been beat on both so. Till now I have won a bid for a car lot it will pay about 57-60 k a year this car lot has over 100 stores and still growing..Any one need work in florida I might sub some out

Talk to the main guy today and he has to get back to me thank god I did a wash and paint on a pool deck for the big boss

Any one spray car lots ?

Ill have all the grounds,And spray all the cars this place is from north to south..ill have more info by the end off the week..One day all us Florida guys need to have a get together

Thanks guys just got in so off to start back at it stay tuned

we will go for round two Ill post how the next step goes after I get done with working. can not wait till its time to fix my belt drive unit that looks much better to fix

Put some money away for the pressure washer from lowes/depot cause the pumps are all junk will break soon the unloaders are all built in to one

From what I see there is the 4 bolts and there is a hole in the flange that had a small screw I got that out just seems like the shaft has a weld from the heat far as the key I think it is inside the shaft.All the shops are a far drive and they are back up for 2 days out.this pump is a AR I need to find a way to break it loose..Thanks for the help along the way

I dont want to smash on it. This unit is a direct drive one inch shaft all I want to do is put this pump on a new 13 h/p the pump has been off to get fix a few times.But I have been at it most of the night now, and not getting any place some one told me about geting 4 long bolts to use as like a pry tool going around even tighten them to see if it pops it off...I dont think any thing will work...What a BEAR OF A JOB

Been looking around for like a rubber paint or mat all I want to do is keep the floor from rotting out just sold old trailer and cleaned it out and it was like a jim sock.. had a leak in the line,and water went all over.So this time with this being new need to seal it.Any one have this in there unit? if so what do you use

Thanks you all read my mind i went to a tractor store and got the kit this trailer is off the ready line so nothing has been on the floor and it looks good.you are right the fumes will knock you out. Thanks

:lgtear: I need a o ring kit for a AR PUMP it is leaking oil all over do not want to run and burn it out. 1 down and i need to find a unloader for a diff machine where can I find a on line store that has it all.I went to ar.com and the site is to dark to read,I went to cats site but have to look up a dealer went to ebay but who knows what you get there..any info

3/4 works well

Ouch!!!!!!!!!!!!

I have the gp hammer head 20 inch surface cleaner and the bar is hiting the abs cover so am sending back to co to get a new one sent.hope this one works well

Where did you find the parts to build one with out getting sold a name and about how much did it cost to make

whats your e-mail I have one you can use

dirt dobbers are freaks of the bees they build such a mud house that will stick to any thing and leave nasty marks on homes