rick77 14 Report post Posted May 6, 2009 Well, the motor blew up today on my 4 gpm 3,000 psi direct drive power washer. It was bound to happen as this machine was a very low end so called commercial power washer. I'll be ordering a belt drive machine tomorrow. I've been under the impression that CAT pumps are the best but what do I know. The machine I'm looking at costs apx $60 bucks more outfitted with a CAT pump instead of a General pump. Is the CAT pump really better and worth the extra $$? Share this post Link to post Share on other sites
chris francis 15 Report post Posted May 6, 2009 Sorry to hear that you lost you motor my machine is same as yours cat pump with commercial honda motor direct drive. is your pump damaged also or just motor. Share this post Link to post Share on other sites
Henry Bockman 14 Report post Posted May 6, 2009 I've got an 11HP belt drive Honda engine if anyone wants it. I won't be needing it. I prefer General Pumps over Cat any day! Share this post Link to post Share on other sites
rick77 14 Report post Posted May 6, 2009 I prefer General Pumps over Cat any day! Any particular reason? Share this post Link to post Share on other sites
rick77 14 Report post Posted May 6, 2009 Sorry to hear that you lost you motor my machine is same as yours cat pump with commercial honda motor direct drive. is your pump damaged also or just motor. I took the pump and drive shaft housing off of the motor and found out that the motor is locked down, not the pump. I don't know if the pump is damaged or not because I can't test it without a motor to drive it. I do know that the pump is not locked down though. Share this post Link to post Share on other sites
Henry Bockman 14 Report post Posted May 6, 2009 Any particular reason? The replacement parts for General Pumps are cheaper and easier to find. Also, in my experience, they just seem to run longer than CAT pumps. I know some guys prefer CAT over General pumps but most of the contractors I know also swear by General Pumps. Every time I talk with other contractors about their favorite equipment three names are always mentioned more than any other. Honda Engines, General Pumps and Becket Burners. Share this post Link to post Share on other sites
rick77 14 Report post Posted May 6, 2009 You'd think that the CAT should be better just going by price alone but higher price doesn't always guarantee a better product. Maybe I'll go with the General pump. I don't know......I'll be ordering from Bob at Pressure Tek so I'll talk with him about the Cat vs. General pump. Share this post Link to post Share on other sites
FullBlast 14 Report post Posted May 6, 2009 I wouldn't give the extra buck for it. General pumps for me. Cat loves living off their name, I'm not saying they are junk but I don't think they are better either. Share this post Link to post Share on other sites
rick77 14 Report post Posted May 6, 2009 A name is just a name. Endorsements from pro power washers speaks for itself. I'm gonna save a bit and get the machine with the General pump. Share this post Link to post Share on other sites
Paul Kassander 26 Report post Posted May 6, 2009 I agree with the above, Cat pumps are good but General is just as good. Share this post Link to post Share on other sites
nlantz 14 Report post Posted May 6, 2009 General Pump's We have been running 2 per truck for over 8 year's with no major problems. Occasional valve replacement's but they take 20 min. We did have one a few years ago where the little oil checking window came off the back and the pump ran dry for as long as it could. It needed total replacement. But I think that was due to employee tampering. We had one cat based portable that struggled if multiple machines were connected to 50gpm water outlets in parking garages. 5 4gpm gp's ran fine 4 gp's and 1 cat the cat struggles. Share this post Link to post Share on other sites
kcpowerclean 14 Report post Posted May 22, 2009 General Pump'sWe have been running 2 per truck for over 8 year's with no major problems. Occasional valve replacement's but they take 20 min. How do you know a valve needs replacing on a pump? Please excuse my ignorance, don't know much about maintenance. Share this post Link to post Share on other sites
Paul Kassander 26 Report post Posted May 22, 2009 The hose will begin to jump or you will feel a vibration/pulsation in the line. This can be caused by debris also so check them before replacing, sometime they can last years. Share this post Link to post Share on other sites