Adrian 155 Report post Posted November 12, 2009 Cleaned up pretty nice. Share this post Link to post Share on other sites
0 FullBlast 14 Report post Posted November 12, 2009 Oh yea, Another quality job done by ABC!!!!!! Share this post Link to post Share on other sites
0 dray5mil 14 Report post Posted November 12, 2009 Sweet ! What was your chemical of choice ? Share this post Link to post Share on other sites
0 PressurePros 249 Report post Posted November 12, 2009 Dryvit.. You southern guys don't seem to have much real stucco? Share this post Link to post Share on other sites
0 dray5mil 14 Report post Posted November 12, 2009 not alot of stucco in this area thats for sure Share this post Link to post Share on other sites
0 Adrian 155 Report post Posted November 13, 2009 It's all the same to me. Dryvit, Stucco, E.I.F.S. I just spit on it as I walked by and it came clean. ( naw I'm just kidding, but it sounded like a Chuck Norris saying) 12% and Prosource soap. Works like a dream. Share this post Link to post Share on other sites
0 Adrian 155 Report post Posted November 13, 2009 hahahahahahahaha spit on it........... ......now that was funny......... How come I am the only one laughing? Boooooooooo get the hook....... Share this post Link to post Share on other sites
0 plainpainter 217 Report post Posted November 13, 2009 I don't have any experience cleaning stucco/dryvit - I hear you guys talk about how hard it is. The one thing I am running into these days that is nearly impossible to clean is Azek material. Especially where the cuts are made and then not sealed - typical examples are corner trim boards with the outward 1" edge along the corner, and the sides of window sills. I really hope this material doesn't take over - as I was experimenting with two stepping with oxalic and simple cherry house wash and then eventually loads of pressure. I only got mediocre results at best - and I live in an area where the siding is mostly painted/stained cedar siding. So I imagine a 'roof' strength cleaner could work well - but would wipe out the surrounding coatings. I see this as a huge problem for the future. Share this post Link to post Share on other sites
0 Adrian 155 Report post Posted November 13, 2009 Just spit on it and it will come clean........ Kidding...... Share this post Link to post Share on other sites
0 RSuds 24 Report post Posted November 13, 2009 I would say that there is a big difference in Dryvit and stucco. Dryvit is a lot easier to clean and stucco will take some pressure if needed. Share this post Link to post Share on other sites
0 Adrian 155 Report post Posted November 13, 2009 Right on. I didn't need any pressure for this one. Shot some reg. mix and dwelled about 15 min., while I grabbed a drink of water. Came back, light rinse it was gone. I agree in the differences between the two, but you know that once you have cleaned the different tpyes so many times in the past. You just gauge it by your mixes strength and get the project finished. Share this post Link to post Share on other sites
0 Adrian 155 Report post Posted November 13, 2009 ....... or just spit on it...... :) Share this post Link to post Share on other sites
0 RSuds 24 Report post Posted November 13, 2009 Got ya. I love doing dryvit it is easy. Share this post Link to post Share on other sites
0 Adrian 155 Report post Posted November 13, 2009 I don't think I can spit that high. NICE PROJECT man. Share this post Link to post Share on other sites
0 RSuds 24 Report post Posted November 14, 2009 That is a good one we do it every year or two. Share this post Link to post Share on other sites
0 PressurePros 249 Report post Posted November 14, 2009 I would say that there is a big difference in Dryvit and stucco. Dryvit is a lot easier to clean and stucco will take some pressure if needed. +1 The mold goes a lot deeper. Sometimes you have to X-Jet str8 12% Share this post Link to post Share on other sites
Cleaned up pretty nice.
Share this post
Link to post
Share on other sites