Lightning Gene 66 Report post Posted May 2, 2008 I have a 8GPM machine and will be stripping old paint from steel fence panels....Who makes the most powerfull Turbo? Share this post Link to post Share on other sites
Sparklean 14 Report post Posted May 2, 2008 Bob sells a few different brands. His Suttner goes up to 5,800 PSI and you can get it in #4, #4.5, #5, #5.5, #6, #7, #8, #10 so I'm sure that will be fine for your 8 GPM machine. Share this post Link to post Share on other sites
David O'Connell Jr. 14 Report post Posted May 2, 2008 We use the PA. Its works great. Share this post Link to post Share on other sites
814jeffw 71 Report post Posted May 2, 2008 Man, I really like the General Rotomax. Seems fast compared to the Suttner I used. Will also shoot a zero degree if needed. Never used feature myself though. Also, make sure you get the filter with it, not even sure why they would sell them without a filter. They have a ceramic orifice and one little particle can ruin your nozzle . Jeff Share this post Link to post Share on other sites
Ron Musgraves 240 Report post Posted May 3, 2008 Dont Drop them Gene... Share this post Link to post Share on other sites
PWkid 79 Report post Posted May 3, 2008 Dont Drop them Gene... HUH?.. Share this post Link to post Share on other sites
Ron Musgraves 240 Report post Posted May 3, 2008 HUH?.. They are fragile Share this post Link to post Share on other sites
Curb Appeal 14 Report post Posted May 12, 2008 This is the best one I've found. I use it for everything. Makes short work of rinsing flatwork. Suttner Dual Turbo Nozzles — 5000 PSI, 36in. Length | Turbo Nozzles | Northern Tool + Equipment Share this post Link to post Share on other sites
Ron Musgraves 240 Report post Posted February 26, 2012 I like the Suttner Also Share this post Link to post Share on other sites
Paul Kassander 26 Report post Posted March 5, 2012 PA makes one of the most agressive 18 degree pattern and they are loaded with a spring washer to keep the nozzle seated on the race. They do have a tendencey to stop spinning sooner than some of the others. Rotomax makes a good one that is inexpensive and will last a long time but you must start it with the nozzle pointed down to prevent damaging the nozzle and race. Suttners are always good but same thing with the nozzle. For me the firs choice is the Rotojet or Suttner. Share this post Link to post Share on other sites
cleanhoods 43 Report post Posted March 6, 2012 How about one that can handle low PSI like 1200 3.5gpm and very hot heat through it like 300+ degrees?? Marko Share this post Link to post Share on other sites
Paul Kassander 26 Report post Posted March 8, 2012 Highest temp rating i have seen is 212 with the pa turbo nozzle. Share this post Link to post Share on other sites
Adrian 155 Report post Posted February 13, 2013 My suttner dual turbo rulezzzzzz!!!!!! I don't use it always, however, it can rip a curb in no time flat when needed. I wonder why it has been discontinued. Share this post Link to post Share on other sites
Ron Musgraves 240 Report post Posted February 13, 2013 didn't know it has Share this post Link to post Share on other sites
Adrian 155 Report post Posted February 13, 2013 I just looked at the link provided. Says they discontinued at Northern. Maybe suttner is just using a different distibutor these days. I swear by my dual suttner. Great tool. But it has the same recoil as a .12 gauge shotgun. Gets the job done. Share this post Link to post Share on other sites
